About Us
Products
Design Services
Support
Contact Us
Home
Contact Us
Sitemap
Multi-Protocol Four Port Serial PCI Card Based on the MPC8260 PowerQUICC II™ Series
Features
  • MPC8250 At Up To 300MHz with Integrated PCI
  • Four SCCs Support a Broad Range of Serial Protocols
  • Software Configurable Serial Interface Modes
  • Front I/O
  • 8-256MB SDRAM
  • 4-16MB Soldered Flash
  • 512KB Socketed Flash
  • 2 KB SEEPROM
  • Two RS-232 SMC Ports
  • VxWorks Driver and BSP
  • Linux LSP
  • Windows NT/2000/XP Driver
Typical Applications
  • LAN/WAN Networking
  • Military Communications
  • Telecommunication Management Network
  • Data and Legacy System Communications
  • Data Acquisition
  • Process Control
Description
XPort1011 is an intelligent communications controller targeting high performance yet low cost applications. XPort1011 combines a wide array of supported serial protocols, a broad range of serial interface standards, and a flexible I/O routing structure, to pack maximum flexibility into an industry standard PCI card.

Powered by the MPC8250 (PowerQUICC II™), XPort1011 implements four serial communication ports providing a EIA-530-A compliant signal set. Supporting HDLC/SDLC, UART, Transparent and BISYNC modes, with NRZ, NRZI, FM0, FM1, Manchester and Differential Manchester encoding. Coupled with software configurable support for RS-232, RS-422, RS-423, RS-485 and MIL-STD-188-114, XPort1011 provides maximum flexibility for your application.

For solutions which require low cost but high performance, the XPort1011 is also available in configurations which provide a 7-wire signal set. This configuration implements four serial communication ports providing TXD, RXD, TXC, RXC, RTS, CTS and DCD flow control, with software configurable support for RS-232, RS-422, RS-423, and RS-485.

As a system designer, XPort1011 will help drive both cost and power consumption out your system. Because the PCI bridge is integrated on chip, XPort1011 draws up to 40% less power, and costs up to 30% less than conventional designs based on other processors.

Processor
  • MPC8250 PowerQUICC II
  • Embedded PowerPC G2 Core
  • 133-300Mhz
  • 280 Dhrystones at 200Mhz
  • 66MHz 60x Bus
  • 16KB Instruction and Data Caches
  • 32KB internal SRAM
  • Integrated MMU
  • Integrated Floating Point Unit
  • Core Disabled Mode supported
Memory
  • 32-256MB SDRAM
  • SDRAM doubles as 8MB of buffer storage in Core Disabled Mode
  • 4-16MB Surface Mount Flash
  • 512KB Socketed Flash
  • 2 KB Serial EEPROM
Serial Communication Controller
  • HDLC, UART, Transparent and BISYNC modes
  • DPLL supporting NRZ, NRZI, FM0, FM1, Manchester and Differential Manchester
  • Independent BRG’s for each SCC transmitter and receiver
  • Optional External Custom Oscillators
Serial Interface (Standard)
  • Software Configurable Drivers for RS-232, RS-422, RS-423, RS-485, and MIL-STD-188-114 Balanced/Unbalanced Type 1 and 2 Modes
  • 10Mbps Max Synchronous
  • 4Mbps Max Asynchronous
  • EIA-530-A DTE/DCE Cable Selectable
Serial Interface (7 Wire)
  • Software Configurable Drivers for RS-232, RS-422, RS-423, and RS-485
  • 10Mbps Max Synchronous
  • 4Mbps Max Asynchronous
  • 7 Wire Interface
  • DTE/DCE Mode Cable Selectable
Software
  • VxWorks BSP
  • SCC and SMC
  • Linux LSP
Physical
  • PCI Form Factor
Power Requirements (Typical)
  • +3.3V 0.60A 1.98W
  • +5.0V 0.35A 1.75W
  • +12.0V 0.012A 0.15W
  • -12.0V 0.012A 0.15W
Operating Temperature
  • 0 to +55C ambient, at board
Humidity
  • 0% to 85%
Storage Temperature
  • -40 to +70C
Copyright © 2006, X-ES
Extreme Engineering Solutions, Inc.
3225 Deming Way, Suite 120
Middleton, WI 53562
Phone: 608-833-1155
Fax: 608-827-6171
Web: http://xes-inc.com
Email: sales@xes-inc.com